Composite Gates Cambridgeshire
We survey, manufacture and fit composite and metal gates across Cambridgeshire and the surrounding fenland — Peterborough, Wisbech and out to King's Lynn. Every gate is measured on site, made to those measurements, and installed by the same people who quoted it.
Coverage moves. We are always reviewing how the installers on our network are performing and taking on new ones as demand grows, so the towns below are where we work most consistently rather than a complete or permanent list.
Towns and cities we cover
The surrounding villages and suburbs of each are covered too. If your town is not named, send your postcode and we will confirm.
Cambridgeshire & the fens
Also covered: March, Whittlesey, Chatteris, Ramsey, Yaxley, Downham Market, Long Sutton and the fen villages.
What we make and fit
- Composite driveway gates Double and single leaf, hung or sliding, manual or automated.
- Composite garden gates Side gates, back gates and matching pedestrian gates.
- Metal gates Steel and metal-framed gates, made to measure.
- Electric gates Automation on new gates, or retro-fitted to existing ones.
- Composite fencing Matching fence panels and screens to tie the boundary together.
What Cambridgeshire asks of a gate
The ground is the first question here, not the last
Fen soil is not ordinary ground. Drained peat and silt behave very differently from clay: they are soft, they hold water, and they settle over years rather than staying put. A post foundation that would be perfectly sound in the Midlands can move on fen ground over a few winters, and the first sign of it is a gate that gradually stops closing cleanly. This is the single most useful thing to get right in this part of the country, and it is decided before anything is dug.
What we do about it
Deeper and wider foundations than a standard detail, sized for what is actually under the opening rather than what is usually under one. Where the ground is particularly soft, a sliding gate can help, because its weight is carried along a track rather than concentrated on two posts. If you know your plot has been made up, drained or built on old workings, say so at survey — it changes the specification and it is far cheaper to allow for than to correct.
Open fen, and very little to break the wind
The fens are flat and largely treeless, so wind arrives with nothing in its way. A tall, fully boarded pair on an open plot acts like a sail, and the load goes straight into the hinges, posts and the soft ground below them — which is the same problem twice over. A partly open infill or a lower top rail lets wind through rather than fighting it, and on wide entrances a sliding gate removes the leverage question altogether.
Wide entrances and working access
Fenland plots tend to come with generous, straight entrances, often shared with agricultural traffic. Wide is not a problem in itself, but past a certain span a swing pair stops making sense and a sliding gate takes over. If the entrance sees tractors and trailers rather than cars, that changes the frame, the running gear and how the gate gets used day to day. Tell us the use as well as the measurement.
What affects the cost
Gate prices move on a handful of variables rather than a fixed rate. The main ones are:
Width of the opening — the single biggest factor, and what decides whether a single leaf, a pair or a sliding gate is appropriate.
Ground conditions — on fen soil this can matter as much as the gate — deeper or wider foundations are common rather than exceptional.
Height and infill — on an open fen plot the infill drives the specification as much as the look does.
Frame and material — composite board on a metal frame, metal only, or composite with a decorative top.
Automation — whether the gate is manual, automated from the start, or built ready for automation later.
Use — an agricultural or yard entrance is specified differently from a domestic driveway of the same width.
FAQs about Composite Gates in Cambridgeshire
Do you cover my village if it is not listed above?
Very likely. The towns listed are where we work most often across Cambridgeshire and the surrounding fens, and the villages around each are covered as a matter of course. Send your postcode and you will get a straight answer either way rather than a maybe.
Does fen ground really affect a gate installation?
Yes, more than almost anything else here. Drained peat and silt are soft and settle over time, so a post foundation that is perfectly sound elsewhere can move over a few winters — and the symptom is a gate that slowly stops closing cleanly. We size foundations for what is actually under the opening rather than to a standard detail.
My plot is on made-up or drained land — should I mention it?
Please do, at survey rather than afterwards. Knowing the history of the ground changes how the posts are set, and allowing for it up front costs a fraction of correcting a gate that has moved. It is one of the few things a customer knows that we cannot see.
Will a gate stand up to wind out on the open fen?
It will if it is specified for it. A partly open infill or a lower top rail lets wind through instead of pushing against the gate, heavier posts set deeper take what remains, and on a wide entrance a sliding gate is supported along its length rather than hanging on two hinges. On soft ground that last point matters twice over.
How wide an opening can you cover?
Wider than most people expect, particularly with a sliding gate, which suits fenland entrances well. The practical limit is the run of clear, reasonably level ground alongside the opening for the gate to track into, rather than the gate itself. We measure that at survey along with the opening.
Not sure you are in range? Send us your postcode and we will confirm whether we can cover you — either way, you will get a straight answer.
Get a free quote← Back to all areas we cover