Composite Gates Staffordshire

We survey, manufacture and fit composite and metal gates across Staffordshire — Stoke-on-Trent and the Potteries, south through Stafford and Cannock to Lichfield and Tamworth, and out into the Moorlands. Every gate is measured on site, made to those measurements, and installed by the same people who quoted it.

Coverage moves. We are always reviewing how the installers on our network are performing and taking on new ones as demand grows, so the towns below are where we work most consistently rather than a complete or permanent list.

Towns and cities we cover

The surrounding villages and suburbs of each are covered too. If your town is not named, send your postcode and we will confirm.

Stoke-on-Trent & the north

Also covered: Newcastle-under-Lyme, Leek, Biddulph, Kidsgrove, Cheadle and the Staffordshire Moorlands villages.

Central Staffordshire

Also covered: Rugeley, Stone, Penkridge, Uttoxeter and the surrounding villages.

South Staffordshire

Also covered: Burntwood, Kingsbury, Barton-under-Needwood and the surrounding areas.

What we make and fit

What Staffordshire asks of a gate

Two very different halves of one county

The Potteries and the southern towns are dense, terraced and urban, where the questions are narrow openings, shared entries and security. The Moorlands and the country between Stafford and Uttoxeter are open, higher and considerably windier, where the question is whether a gate will still be hanging true in five years. It is one of the few counties where the right specification genuinely changes from one end to the other, and it is worth saying which end you are at when you enquire.

Exposure in the Moorlands and on the Chase

Get onto higher ground towards the Moorlands, or the open country around Cannock Chase, and wind becomes the governing factor. A tall, fully boarded pair on an open plot is a sail, and all of that load ends up in the hinges, posts and foundations. A partly open infill or a lower top rail lets wind through, and heavier posts set deeper take what remains. On exposed sites that is the specification, not an upgrade.

Old industrial ground

Parts of the county carry a long industrial history, and the ground reflects it — made-up land, old workings and fill are not unusual around the Potteries and the former coalfield. That matters for post foundations, because a detail that is fine in undisturbed clay can settle over a few winters, and the first symptom is a gate that stops closing cleanly. If you know the history of the plot, tell us at survey.

Equestrian and rural access

Staffordshire has a great deal of equestrian and smallholding property, and those entrances ask different questions from a domestic driveway. Wider spans, heavier use, and gates that need to close reliably every time rather than most of the time. Height and gaps matter too where horses are involved. It is all workable, but it needs saying at enquiry stage so the gate is specified for the job it is actually doing.

What affects the cost

Gate prices move on a handful of variables rather than a fixed rate. The main ones are:

Width of the opening — the single biggest factor, and what decides whether a single leaf, a pair or a sliding gate is appropriate.

Height and infill — on exposed ground the infill drives the specification as much as the appearance does.

Frame and material — composite board on a metal frame, metal only, or composite with a decorative top.

Automation — whether the gate is manual, automated from the start, or built ready for automation later.

Ground conditions — made-up or previously worked ground can need deeper or wider post foundations.

Use — an equestrian or yard entrance is specified differently from a domestic driveway of the same width.

FAQs about Composite Gates in Staffordshire

Do you cover my town if it is not listed above?

Very likely. The towns listed are where we work most often across Staffordshire, from the Potteries down to Lichfield and Tamworth, and the surrounding villages of each are covered as a matter of course. Send your postcode and you will get a straight answer either way rather than a maybe.

What changes on an exposed site in the Moorlands?

The infill, the posts and the foundations. Wind load on a tall solid gate is considerable, and on open high ground it is the thing most likely to shorten its life. A partly open infill or a lower top rail lets wind through, and heavier posts set deeper carry the rest. It is specified once we have seen how exposed the opening really is, not assumed from the postcode.

Does old industrial or made-up ground affect the installation?

It can, and it is worth mentioning if you know the history of the plot. Post foundations that are perfectly sound in undisturbed clay can settle in fill or previously worked ground, and the symptom shows up a couple of winters later as a gate that no longer closes cleanly. Where we expect it, posts go deeper or wider rather than to a standard detail.

Can you do gates for a yard or equestrian entrance?

Yes, and they are specified differently from a domestic gate of the same width — heavier use, wider spans, and a gate that has to latch reliably every time. Where horses are involved, height and the size of gaps matter as well. Tell us the use as well as the measurement when you enquire and the gate gets built for the job.

Is a composite gate suitable for a farm or working entrance?

Often, though it depends on the traffic. Composite handles weather and needs no repainting, which suits an entrance nobody has time to maintain. Where an opening takes agricultural vehicles or very heavy use, the frame specification matters more than the board, and we would talk you through a metal-framed option rather than assume composite is automatically right.

Not sure you are in range? Send us your postcode and we will confirm whether we can cover you — either way, you will get a straight answer.

Get a free quote

← Back to all areas we cover